Data as of: 2026-08-05 Administration DE EN
Plant Protection Product Search

« Products

QuickPhos Pellets

Authorisation number: 006278-60 Distribution extension

Formulation
Gas generating product
first authorised
2015-07-30
authorised until
2027-11-30
Field of activity
Insecticide
Hazard to bees
B3 – not hazardous to bees given the prescribed use
Trial designation
10130-20859-I-0-GE

Active substances

Active substanceEnglish name ContentBasis Type of substanceEU approved
Aluminiumphosphid aluminium phosphide 570 g/kg parent structure Wirkstoff yes

The chemical group (such as guanidines) is not provided by the BVL interface and therefore cannot be shown.

Modes of action

Code Mode of action Text
WMI24A Mode of Action (IRAC-Group): 24A

The BVL records the mode of action as a WM-series condition; the group follows the FRAC, HRAC or IRAC classification.

Holder and distribution

Authorisation holder
UPL Holdings Coöperatief U.A. (NL)
Distribution
UPL Deutschland GmbH (DE)

Authorised uses (1)

CropPest Area of use Hazard to bees Use no.
stored cereals, (-) maize Insects Gas-tight silo unit without circulatory fumigation 006278-60/00-001

Conditions of use

Code Text Crop Buffer zone
NW467 The product and its remains, empty containers and packaging and rinsing fluids must not be dumped in water. This also applies to indirect entry via the urban or agrarian drainage system and to rain-water and sewage canals.

Restrictions

Code Text Crop Buffer zone
SB001 Avoid any unnecessary contact with the product. Misuse can lead to health damage.
SF5053 Phosphane develops in the air or in combination with moisture; it is an odourless gas which is very toxic for humans and animals, it is corrosive and is both highly flammable and self-igniting when exposed to air. Occasionally there is a garlic-, fish- or carbide-like smell caused by impurities. This smell alone is not a reliable indication of phosphane since it can easily be adsorbed by soil and other materials and is often not apparent until health limits have been exceeded.
SB110 The directive concerning requirements for personal protective gear in plant protection, "Personal protective gear for handling plant protection products" of the Federal Office of Consumer Protection and Food Safety must be observed.
SB195 Suitable equipment and resources must be used for applying the preparation. Contact with the skin must be avoided.
SE1201 Wear tight fitting eye protection when applying/handling the product.
SF510 If an applicator is used to apply the plant protection product, this must be cleaned according to point 9 par. (5) of 'TRGS' 512 (technical regulations for dangerous substances) after use. The equipment must be cleaned in the open and preferably when there is a light wind (paying attention to the wind direction), taking care to avoid exposing humans and animals to dust from the plant protection product and/or phosphane. The applicator should be cleaned in a sufficiently large container with low-surface tension water (with a rinsing agent). The entire parts must remain in the water bath for at least four hours. The area must be vacated during the procedure. The equipment must then be rinsed thoroughly with fresh water until all the parts are clean. The equipment must undergo a technical inspection before reuse and all the parts must be absolutely dry.
SS2204 Wear a protective suit for plant protection products and sturdy shoes (e.g. rubber boots) when applying/handling the product.
SF514-1 The operator or person equipped with adequate experience responsible for measuring the fumigation product used must check the ambient air regularly in accordance with 'TRGS' (technical regulation for dangerous substances) 512 (fumigations) until the area has been authorised for access to ensure that concentrations of the fumigation product which exceed the limit of detection (more than or equal to 0.01 ppm) do not occur outside of the specified danger zone. The measurement results and, if appropriate, the measures taken, must be documented and kept together with the fumigation documentation.
SF524 Rooms/stores must be vacated and closed immediately after fumigation has been started. For use under gas-tight sheeting, put the goods in gas-tight packaging and vacate the danger zone immediately after fumigation has started.
SS1201 Wear standard protective gloves (plant protection) when handling/applying the product.
ST3312 Wear respiratory equipment with filter (type/identification colour ...*)) for phosphane when applying/handling the product and suitable protective clothing according to TRGS 512. *) state respiratory equipment, gas filter type (identification letter and colour) and gas filter class.
VS005-1 Fumigations with substances stated in "GefStoffV" (Hazardous Substances Ordinance) annex I no.4.1 (1) till (3) require permission according to GefStoffV annex I no. 4.2 (1). When applying the product, the special regulations in GefStoffV annex I no. 4 in addition to the technical regulations for hazardous substances (TRGS 512 - Fumigations) must be observed.
WMI24A Mode of Action (IRAC-Group): 24A
DH001 RSh 1: Toxic in contact with the eyes.
EO001 SPo1: After contact with skin, first remove product with dry cloth and then wash with plenty of water.
EO002 SPo2: Wash all protective cloth after use.
EO004 SPo 4: The container must be opend outdoors and in dry conditions.
NW262 The product is toxic for algae.
NW264 The product is toxic for fish and aquatic invertebrates.

Notes

Hazard classification (GHS/CLP)

Signal word

Hazard pictograms

Hazard statements

Distribution extensions

Further information

Data source: PSM-API · Data as of: 2026-08-05

Only the authorisation notice together with the product label and instructions for use is legally binding.